Top 10 typical forklift crashes ， forklift procedure need to take notice of these issues ！.

Don't take too lightly the forklift at work. If the procedure is not good, there will certainly be major mishaps in minutes, and there are several mishaps including forklifts.

Instance 1: The forklift cargo obstructed the motorist's sight, and the individual in front might not be found, causing a rolling accident.
Case 2: In order to maintain the balance of the forklift when raising hefty items, the staff members utilized their body weight as the counterweight, which almost caused casualties.
Instance 3: The size of the forklift freight exceeds the permitted size of the route and hangs on the roadside shelf, which virtually creates an crash.
Case 4: Forklift is speeding and rolls over during a turn.
Case 5: The forklift vehicle driver did not discover the pedestrian, and the pedestrian did not discover the forklift.
Case 6: The forklift lifts the employees illegally, the forklift driver does not put on the safety belt, the forklift lifter falls and the driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not put on a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift procedure ought to take note of these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn initially and after that start.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be secure before beginning.
3. When the forklift starts with a lots, the chauffeur needs to first validate that the load is secure and reputable.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole should be slanted backwards. .
2. Do not raise the fork too expensive when driving. When getting in and leaving the job website or while driving, be careful that there will be no barriers in the sky. When the tons is taking a trip, the fork must not be increased expensive, which will certainly affect the stability of the forklift. .
3. After dumping, the fork should be reduced to the regular driving placement before driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal must be released first. High-speed sharp turns are prohibited. High-speed doglegs will trigger the lorry to lose lateral stability and tip over. .
5. When the forklift is downhill, it is purely restricted to shut off the fire and slide, and it is restricted to brake all of a sudden while driving with tons unless there are special situations.
6. When the forklift is running, it has to obey the website traffic rules in the factory and must keep a certain safety distance from the lorry ahead. .
7. When the forklift is running, the lots needs to remain in the lowest setting that does not impede the driving, and the gantry should be correctly tilted back. The load shall not be raised except when stacking or filling. .
8. The elevation of the lots need to not block the chauffeur's sight. In special circumstances, when the item impacts the forward vision, drive at a low speed when reversing.
9. It is prohibited to activate the ramp, neither to drive across the ramp. .
10. The safe driving speed of the forklift in the manufacturing facility area is 5 km/h, and it has to drive securely at a reduced rate when going into the production workshop area. .
11. When the forklift is lifted, lifted or driven, it is forbidden for workers to stand on the fork to hold items and play a stabilizing function. .
12. If issues are located, they will certainly be fixed and reported in a prompt way, and they will certainly never ever operate with diseases or hide them.

loading and unloading.
1. When fork-loading products, the distance in between both forks should be adjusted as needed to make the lots of both forks balanced and not manipulated, and one side of the product must be against the shelf. .
2. It is prohibited to work with a single fork or use a fork top or pull. In unique situations, security warning signs need to be established to advise surrounding pedestrians. .
3. In the process of filling and unloading items, the forklift must be stopped with the brake. .
4. The rate of the vehicle must be slow and stable. Beware not to roll the wheels on the dunnage, so as not to extend the rolled things and harm individuals. .
5. When utilizing a fork to fork the goods, the fork ought to be as deep as feasible under the lots, and it needs to be kept in mind that the fork pointer ought to not touch other items or objects. The tons must be maintained with minimal back tilt of the gantry to make sure that the load does not glide in reverse. The mast can be tilted forward a little when the lots is lowered to permit simple placement of the load and removal of the forks. .
6. It is restricted to fork items at broadband and ram hard objects with the fork head. .
7. When the forklift is functioning, it is forbidden for people to loaf the fork, so regarding stay clear of the collapse of the goods and harm people. .
8. Overwhelming is forbidden, and it is banned to make use of forks to lift employees to participate in high-altitude procedures to prevent high-altitude falling mishaps. .
9. It is not permitted to utilize the brake inertia to slide, put, round or roll items. .
10. It is not enabled to use forks to select, turn pallet unload.

Leaving .
1. It is restricted to leave the forklift when Stand-on Electric Pallet Stacker the things on the fork impend. Prior to leaving the forklift, you must dump the goods or lower the fork frame.
2. Draw the hand brake deal with to dead or dispirit the hand brake button.
3. The engine is shut off and the power is removed. (Except for unique situations, such as the vehicle driver does not leave the automobile's view and does not surpass 1 minute).
4. Remove the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance ought to be inspected, and fuel, lubing oil and cooling water need to be added.
2. Inspect the safety efficiency of beginning, running and stopping.
3. Inspect whether the lights and horn signals are full and effective.
4. During the procedure of the forklift, check whether the stress and temperature are regular.
5. After the forklift is running, the external leak needs to likewise be examined and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You need to inspect before leaving the cars and truck;.
2. When you encounter Stand-on Electric Pallet Stacker someone in front of you throughout driving, you need to send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not surpass 5 km/h;.
4. When driving, the nadir of the cargo should be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be also sharp to stop the propensity of " complimentary turning";.
6. Adding and down the incline needs to be slow-moving and uniform, and no turning on the incline is enabled.
7. Do not drive throughout the gradient. When the slope is more than 10%, the lorry should be driven backwards when declining;.
8. When the forklift workers carry the goods and move forward, if they run into huge or heavy items and most likely to the vehicle driver's view, they must take the turning around exercise
.
The "Eight Prohibitions" should be followed in the procedure.
1. Solitary fork procedure is not enabled.
2. It is not enabled to lift the goods for long distance driving.
3. It is not allowed to pick up the goods by turning over the pallet with the fork.
4. It is not allowed to straight shovel chemicals, flammables and various other dangerous chemicals with forks.
5. It is not permitted to utilize inertia force to grab the goods.
6. It is not permitted to utilize stopping pressure to exile round or easy-to-roll things.
7. It is not allowed to bring people to deal with the pallet or fork, and it is purely prohibited to stand under the fork after the fork is elevated.
8. Do not drive side to side on slopes
.
Car park is not allowed under the list below conditions.
1. Curves, narrow roads, train crossings;.
2. Sections with a longitudinal incline above 5%.
3. When there is an obstacle on one side of the road, the contrary side of the area with the very same length as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844